hi3519多sensor设置说明

小咪咪 2022-09-10 15:25 291阅读 0赞

# hi3519多sensor设置说明 #

## mipi接口模式与设备号 ##

3519总共有12-lane输入,从手册上看支持12lane,8lane+4lane,4lane+4x2lane  
SDK中从mipi\_rx.c文件mipi\_print\_lane\_divide\_mode函数可以区分mipi模式

static const char *mipi_print_lane_divide_mode(lane_divide_mode_t mode)
    { 
        switch (mode) { 
            case LANE_DIVIDE_MODE_0:
                return "12";
    
            case LANE_DIVIDE_MODE_1:
                return "8+4";
    
            case LANE_DIVIDE_MODE_2:
                return "8+2+2";
    
            case LANE_DIVIDE_MODE_3:
                return "4+8";
    
            case LANE_DIVIDE_MODE_4:
                return "4+4+4";
    
            case LANE_DIVIDE_MODE_5:
                return "4+4+2+2";
    
            case LANE_DIVIDE_MODE_6:
                return "4+2+2+2+2";
    
            default:
                break;
        }
    
        return "N/A";
    }

LANE\_DIVIDE\_MODE\_4对应的是3个4lane接口  
LANE\_DIVIDE\_MODE\_6对应的是5个4lane+2lane+2lane+2lane+2lane接口  
目前我只测试了LANE\_DIVIDE\_MODE\_6模式的1个4lane sensor和LANE\_DIVIDE\_MODE\_4模式的2个4lane sensor  
由于最开始不了解，默认代码里一个sensor时是使用的LANE\_DIVIDE\_MODE\_6模式  
然后通过mipi\_rx\_hal.c中mipi\_rx\_drv\_is\_lane\_valid函数可以确认每个通道对应的设备号

int mipi_rx_drv_is_lane_valid(combo_dev_t devno, short lane_id, lane_divide_mode_t mode)
    { 
        int lane_valid = 0;
    
        switch (mode) { 
            case LANE_DIVIDE_MODE_0:
                if (devno == 0) { 
                    if (0 <= lane_id && lane_id <= 11) { 
                        lane_valid = 1;
                    }
                }
                break;
            case LANE_DIVIDE_MODE_1:
                if (devno == 0) { 
                    if (0 <= lane_id && lane_id <= 7) { 
                        lane_valid = 1;
                    }
                } else if (devno == 3) { 
                    if (8 <= lane_id && lane_id <= 11) { 
                        lane_valid = 1;
                    }
                }
                break;
            case LANE_DIVIDE_MODE_2:
                if (devno == 0) { 
                    if (0 <= lane_id && lane_id <= 7) { 
                        lane_valid = 1;
                    }
                } else if (devno == 3) { 
                    if (lane_id == 8 || lane_id == 10) { 
                        lane_valid = 1;
                    }
                } else if (devno == 4) { 
                    if (lane_id == 9 || lane_id == 11) { 
                        lane_valid = 1;
                    }
                }
                break;
            case LANE_DIVIDE_MODE_3:
                if (devno == 0) { 
                    if (0 <= lane_id && lane_id <= 3) { 
                        lane_valid = 1;
                    }
                } else if (devno == 1) { 
                    if (4 <= lane_id && lane_id <= 11) { 
                        lane_valid = 1;
                    }
                }
                break;
            case LANE_DIVIDE_MODE_4:
                if (devno == 0) { 
                    if (0 <= lane_id && lane_id <= 3) { 
                        lane_valid = 1;
                    }
                } else if (devno == 1) { 
                    if (4 <= lane_id && lane_id <= 7) { 
                        lane_valid = 1;
                    }
                } else if (devno == 3) { 
                    if (8 <= lane_id && lane_id <= 11) { 
                        lane_valid = 1;
                    }
                }
                break;
            case LANE_DIVIDE_MODE_5:
                if (devno == 0) { 
                    if (0 <= lane_id && lane_id <= 3) { 
                        lane_valid = 1;
                    }
                } else if (devno == 1) { 
                    if (4 <= lane_id && lane_id <= 7) { 
                        lane_valid = 1;
                    }
                } else if (devno == 3) { 
                    if (lane_id == 8 || lane_id == 10) { 
                        lane_valid = 1;
                    }
                } else if (devno == 4) { 
                    if (lane_id == 9 || lane_id == 11) { 
                        lane_valid = 1;
                    }
                }
                break;
            case LANE_DIVIDE_MODE_6:
                if (devno == 0) { 
                    if (0 <= lane_id && lane_id <= 3) { 
                        lane_valid = 1;
                    }
                } else if (devno == 1) { 
                    if (lane_id == 4 || lane_id == 5) { 
                        lane_valid = 1;
                    }
                } else if (devno == 2) { 
                    if (lane_id == 6 || lane_id == 7) { 
                        lane_valid = 1;
                    }
                } else if (devno == 3) { 
                    if (lane_id == 8 || lane_id == 9) { 
                        lane_valid = 1;
                    }
                } else if (devno == 4) { 
                    if (lane_id == 10 || lane_id == 11) { 
                        lane_valid = 1;
                    }
                }
                break;
            default:
                break;
        }
    
        return lane_valid;
    }

最终模式设置是在sample\_comm\_vi.c中SAMPLE\_COMM\_VI\_StartMIPI函数  
会调用SAMPLE\_COMM\_VI\_SetMipiHsMode(LANE\_DIVIDE\_MODE\_4)设置mipi模式

## 接口配置主要代码 ##

sample\_comm\_vi.c文件SAMPLE\_COMM\_VI\_GetComboAttrBySns函数  
根据上面设置的mipi模式对各通道参数进行设置，以LANE\_DIVIDE\_MODE\_4模式进行说明

combo_dev_attr_t MIPI_4lane_CHN0 =
    { 
        .devno = 0,
        .input_mode = INPUT_MODE_MIPI,
        .data_rate = MIPI_DATA_RATE_X1,
        .img_rect = { 0, 0, 1920, 1080},
    
        { 
            .mipi_attr =
            { 
                DATA_TYPE_RAW_10BIT,
                HI_MIPI_WDR_MODE_NONE,
                { 0, 1, 2, 3, -1, -1, -1, -1}
            }
        }
    };
    combo_dev_attr_t MIPI_4lane_CHN1 =
    { 
        .devno = 1,
        .input_mode = INPUT_MODE_MIPI,
        .data_rate = MIPI_DATA_RATE_X1,
        .img_rect = { 0, 0, 1920, 1080},
    
        { 
            .mipi_attr =
            { 
                DATA_TYPE_RAW_10BIT,
                HI_MIPI_WDR_MODE_NONE,
                { 4, 5, 6, 7, -1, -1, -1, -1}
            }
        }
    };
    combo_dev_attr_t MIPI_4lane_CHN2 =
    { 
        .devno = 3,
        .input_mode = INPUT_MODE_MIPI,
        .data_rate = MIPI_DATA_RATE_X1,
        .img_rect = { 0, 0, 1920, 1080},
    
        { 
            .mipi_attr =
            { 
                DATA_TYPE_RAW_10BIT,
                HI_MIPI_WDR_MODE_NONE,
                { 8, 9, 10, 11, -1, -1, -1, -1}
            }
        }
    };

分别对应硬件接口MIPI0,MIPI1,MIPI2  
最后面那个devno为3具体是根据mipi\_rx\_hal.c中mipi\_rx\_drv\_is\_lane\_valid函数LANE\_DIVIDE\_MODE\_4模式中的代码进行确认

## 测试代码vi配置 ##

双sensor主要配置

SAMPLE_COMM_VI_GetSensorInfo(&stViConfig);
    
    stViConfig.s32WorkingViNum                                   = 2;
    stViConfig.as32WorkingViId[0]                                = 0;
    stViConfig.astViInfo[0].stSnsInfo.s32BusId        = 1;
    stViConfig.astViInfo[0].stSnsInfo.MipiDev         = ViDev[0];
    stViConfig.astViInfo[0].stDevInfo.ViDev           = ViDev[0];
    stViConfig.astViInfo[0].stDevInfo.enWDRMode       = enWDRMode;
    stViConfig.astViInfo[0].stPipeInfo.enMastPipeMode = enMastPipeMode;
    stViConfig.astViInfo[0].stPipeInfo.aPipe[0]       = ViPipe[0];
    stViConfig.astViInfo[0].stPipeInfo.aPipe[1]       = -1;
    stViConfig.astViInfo[0].stPipeInfo.aPipe[2]       = -1;
    stViConfig.astViInfo[0].stPipeInfo.aPipe[3]       = -1;
    stViConfig.astViInfo[0].stChnInfo.ViChn           = ViChn;
    stViConfig.astViInfo[0].stChnInfo.enPixFormat     = enPixFormat;
    stViConfig.astViInfo[0].stChnInfo.enDynamicRange  = enDynamicRange;
    stViConfig.astViInfo[0].stChnInfo.enVideoFormat   = enVideoFormat;
    stViConfig.astViInfo[0].stChnInfo.enCompressMode  = enCompressMode;
    
    stViConfig.as32WorkingViId[1]                                = 1;
    stViConfig.astViInfo[1].stSnsInfo.MipiDev         = ViDev[1];
    stViConfig.astViInfo[1].stSnsInfo.s32BusId        = 5;
    stViConfig.astViInfo[1].stDevInfo.ViDev           = ViDev[1];
    stViConfig.astViInfo[1].stDevInfo.enWDRMode       = enWDRMode;
    stViConfig.astViInfo[1].stPipeInfo.enMastPipeMode = enMastPipeMode;
    stViConfig.astViInfo[1].stPipeInfo.aPipe[0]       = ViPipe[1];
    stViConfig.astViInfo[1].stPipeInfo.aPipe[1]       = -1;
    stViConfig.astViInfo[1].stPipeInfo.aPipe[2]       = -1;
    stViConfig.astViInfo[1].stPipeInfo.aPipe[3]       = -1;
    stViConfig.astViInfo[1].stChnInfo.ViChn           = ViChn;
    stViConfig.astViInfo[1].stChnInfo.enPixFormat     = enPixFormat;
    stViConfig.astViInfo[1].stChnInfo.enDynamicRange  = enDynamicRange;
    stViConfig.astViInfo[1].stChnInfo.enVideoFormat   = enVideoFormat;
    stViConfig.astViInfo[1].stChnInfo.enCompressMode  = enCompressMode;

其中ViDev对应上面说到的devno  
s32BusId为具体硬件接口上的i2c总线  
主要修改就是这些地方.  
主要测试了mipi0掊一路4lane sensor  
mipi0,mipi1各接一路4lane sensor  
mipi0,mipi2各接一路4lane sensor  
都能正常进行编码

======================================  
作者：hclydao  
http://blog.csdn.net/hclydao  
版权没有，但是转载请保留此段声明

===========================================