6.3.3Transmit ONOFF time mask

雨点打透心脏的1/2处 2023-01-19 07:25 10阅读 0赞

# 1、测试目的 #

验证通用的ON / OFF时间掩码是否满足6.3.3.2.5的要求。

发送开/关时间掩码定义了允许的瞬态周期

\-在发送OFF电源和发送ON电源符号之间（发送ON / OFF）

除非另有说明，否则第6.5节中的最低要求也适用于过渡时期。

错误功率的传输增加了对其他信道的干扰，或者增加了上行链路信道中的传输错误。

# 2、测试适用性 #

此测试案例适用于所有类型的NR UE版本15及更高版本。

# 3、测试说明 #

## 1、初始条件 ##

初始条件是需要测试UE的一组测试配置，以及SS与UE一起采取的步骤以达到正确的测量状态。

初始测试配置包括环境条件，测试频率，测试信道带宽和基于表5.2-1中指定的NR工作频带的子载波间隔。 所有这些配置均应使用适用的测试参数针对测试信道带宽和子载波间隔的每种组合进行测试，如表6.3.3.2.4.1-1所示。 上行链路参考测量信道（RMC）的细节在附件A.2中规定。 测量前的PDSCH和PDCCH的配置在附件C.2中规定。

**Table 6.3.3.2.4.1-1: Test Configuration Table**

<table style="margin-left:18.9pt;"> 
 <tbody> 
 <tr> 
 <td colspan="4" style="vertical-align:top;"> Initial Conditions </td> 
 </tr> 
 <tr> 
 <td colspan="2" style="vertical-align:top;"> Test Environment as specified in TS 38.508-1 [10] subclause 4.1 </td> 
 <td colspan="2" style="vertical-align:top;"> Normal </td> 
 </tr> 
 <tr> 
 <td colspan="2" style="vertical-align:top;"> Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1 </td> 
 <td colspan="2" style="vertical-align:top;"> Low range, Mid range, High range </td> 
 </tr> 
 <tr> 
 <td colspan="2" style="vertical-align:top;"> Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1 </td> 
 <td colspan="2" style="vertical-align:top;"> Lowest, Mid, Highest </td> 
 </tr> 
 <tr> 
 <td colspan="2" style="vertical-align:top;"> Test SCS as specified in Table 5.3.5-1. </td> 
 <td colspan="2" style="vertical-align:top;"> Highest </td> 
 </tr> 
 <tr> 
 <td colspan="4" style="vertical-align:top;"> Test Parameters </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> Downlink Configuration </td> 
 <td colspan="2" style="vertical-align:top;"> Uplink Configuration </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> Test ID </td> 
 <td style="vertical-align:top;"> N/A for maximum output power test case </td> 
 <td style="vertical-align:top;"> Modulation </td> 
 <td style="vertical-align:top;"> RB allocation (NOTE 1) </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> 1 </td> 
 <td style="vertical-align:top;"> DFT-s-OFDM QPSK </td> 
 <td style="vertical-align:top;"> Outer_Full </td> 
 </tr> 
 <tr> 
 <td colspan="4" style="vertical-align:top;"> NOTE 1:&nbsp;&nbsp; 在表6.1-1中为PC2，PC3和PC4定义了每个RB分配的特定配置，而对于PC1则定义了表6.1-2。 </td> 
 </tr> 
 </tbody> 
</table>

## 2、测试步骤 ##

1. SS通过PDCCH DCI格式0\_1发送带有针对C\_RNTI的TPC命令0dB的每个UL HARQ过程的上行链路调度信息，以根据表6.3.3.2.4.1-1调度UL RMC。由于UE没有有效载荷并且没有环回数据要发送，因此UE在UL RMC上发送上行链路MAC填充比特。

2.如附件K.1.1所述，将UE设置为通过3D EIRP扫描找到的带内Tx波束峰值方向。至少允许BEAM\_SELECT\_WAIT\_TIME（NOTE 4）才能完成UE Tx波束选择。

3. SS仅通过使用条件Tx执行TS 38.508-1 \[10\]第4.9.2节中指定的过程来激活UE Beamlock功能（UBF）。

4.对于UE发射关闭功率，根据测试配置，在无线电接入模式的信道带宽内，在Tx波束峰值方向上测量UE EIRP，应满足表6.3.3.2.5-1中所述的要求。 EIRP测试程序在附件K.1.3中定义。测量的周期应为PUSCH传输之前的时隙，时隙末尾的5 µs瞬态周期和任何DL周期除外。 EIRP的计算考虑了两个极化角theta和phi。

5.对于UE发射ON功率，根据测试配置，在无线电接入模式的信道带宽内，在Tx波束峰值方向上测量UE EIRP，应满足表6.3.3.2.5-2中描述的要求。 EIRP测试程序在附件K中定义。测量周期应为一个带有PUSCH传输的时隙。 EIRP的计算考虑了两个极化角theta和phi。对于TDD，仅由UL符号组成的时隙正在测试中。

6.对于UE发射关闭功率，根据测试配置，在无线电接入模式的信道带宽内，在Tx波束峰值方向上测量UE EIRP，这应满足表6.3.3.2.5-1中所述的要求。 EIRP测试程序在附件K.1.3中定义。测量周期应为PUSCH传输后的时隙，不包括时隙开始处的5 µs瞬态周期和任何DL周期。 EIRP的计算考虑了两个极化角theta和phi。

7. SS通过执行TS 38.508-1 \[10\]第4.9.3节中指定的过程来停用UE Beamlock功能（UBF）。

# 4、消息内容 #

消息内容符合TS 38.508-1 \[10\] 4.6节的规定，但以下情况除外。

**Table 6.3.3.2.4.3-1: *PUSCH-ConfigCommon***

<table> 
 <tbody> 
 <tr> 
 <td colspan="4" style="vertical-align:top;"> Derivation Path: TS 38.508-1[10], Table 4.6.3-119 </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> Information Element </td> 
 <td style="vertical-align:top;"> Value/remark </td> 
 <td style="vertical-align:top;"> Comment </td> 
 <td style="vertical-align:top;"> Condition </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> PUSCH-ConfigCommon ::= SEQUENCE { </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; p0-NominalWithGrant </td> 
 <td style="vertical-align:top;"> -102 </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> 50MHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> -106 </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> 100MHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> -108 </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> 200MHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> -112 </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> 400MHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> } </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 </tbody> 
</table>

**Table 6.3.3.2.4.3-2: ServingCellConfigCommon**

<table> 
 <tbody> 
 <tr> 
 <td colspan="4" style="vertical-align:top;"> Derivation Path: 38.508-1[5], Table 4.6.3-168 </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> Information Element </td> 
 <td style="vertical-align:top;"> Value/remark </td> 
 <td style="vertical-align:top;"> Comment </td> 
 <td style="vertical-align:top;"> Condition </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> ServingCellConfigCommon ::= SEQUENCE { </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; ss-PBCH-BlockPower </td> 
 <td style="vertical-align:top;"> 4 </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> SCS_120kHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> 7 </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> SCS_240kHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> } </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 </tbody> 
</table>

<table> 
 <tbody> 
 <tr> 
 <td style="vertical-align:top;"> Condition </td> 
 <td style="vertical-align:top;"> Explanation </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> SCS_120kHz </td> 
 <td style="vertical-align:top;"> SCS=120kHz for SS/PBCH block </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> SCS_240kHz </td> 
 <td style="vertical-align:top;"> SCS=240kHz for SS/PBCH block </td> 
 </tr> 
 </tbody> 
</table>

**Table 6.3.3.2.4.3-3: PUSCH-PowerControl**

<table> 
 <tbody> 
 <tr> 
 <td colspan="4" style="vertical-align:top;"> Derivation Path: TS 38.508-1 [10], Table 4.6.3-120 </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> Information Element </td> 
 <td style="vertical-align:top;"> Value/remark </td> 
 <td style="vertical-align:top;"> Comment </td> 
 <td style="vertical-align:top;"> Condition </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> PUSCH-PowerControl ::= SEQUENCE { </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; tpc-Accumulation </td> 
 <td style="vertical-align:top;"> disabled </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; p0-AlphaSets SEQUENCE (SIZE (1..maxNrofP0-PUSCH-AlphaSets)) OF SEQUENCE { </td> 
 <td style="vertical-align:top;"> 1 entry </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp;&nbsp;&nbsp; P0-PUSCH-AlphaSet[1] SEQUENCE { </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; alpha </td> 
 <td style="vertical-align:top;"> alpha1 </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp;&nbsp;&nbsp; } </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> &nbsp; } </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;"> } </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 <td style="vertical-align:top;"> &nbsp; </td> 
 </tr> 
 </tbody> 
</table>

# 5、测试要求 #

**Table 6.3.3.2.5-1: Test requirement of OFF power of General ON/OFF time mask**

<table> 
 <tbody> 
 <tr> 
 <td style="vertical-align:top;width:82.1pt;"> &nbsp; </td> 
 <td colspan="4" style="width:328.5pt;"> Channel bandwidth / minimum output power / measurement bandwidth </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;width:82.1pt;"> &nbsp; </td> 
 <td style="width:82.1pt;"> 50 MHz </td> 
 <td style="width:82.1pt;"> 100 MHz </td> 
 <td style="width:82.15pt;"> 200 MHz </td> 
 <td style="width:82.15pt;"> 400 MHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;width:82.1pt;"> Transmit OFF power </td> 
 <td colspan="4" style="width:328.5pt;"> ≤ -30+TT+R dBm </td> 
 </tr> 
 <tr> 
 <td style="width:82.1pt;"> Transmission OFF Measurement bandwidth </td> 
 <td style="width:82.1pt;"> 47.58 MHz </td> 
 <td style="width:82.1pt;"> 95.16 MHz </td> 
 <td style="width:82.15pt;"> 190.20 MHz </td> 
 <td style="width:82.15pt;"> 380.28 MHz </td> 
 </tr> 
 <tr> 
 <td colspan="5" style="width:410.6pt;"> NOTE 1:&nbsp;&nbsp; 由于可测试性问题，无法测试核心要求，并且测试要求包括宽松要求以实现从测试系统噪声到测量结果的影响= 1.0 dB（最小要求+宽松R）。 NOTE 2:&nbsp;&nbsp; 宽松R在表6.3.3.2.5-5中规定。 </td> 
 </tr> 
 </tbody> 
</table>

**Table 6.3.3.2.5-2: Test requirement of ON power of General ON/OFF time mask**

<table> 
 <tbody> 
 <tr> 
 <td style="vertical-align:top;width:81.7pt;"> &nbsp; </td> 
 <td style="vertical-align:top;width:35.45pt;"> SCS </td> 
 <td colspan="4" style="width:7cm;"> Channel bandwidth / measurement bandwidth </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;width:81.7pt;"> &nbsp; </td> 
 <td style="vertical-align:top;width:35.45pt;"> [kHz] </td> 
 <td style="width:47.8pt;"> 50 MHz </td> 
 <td style="width:49.6pt;"> 100 MHz </td> 
 <td style="width:49.6pt;"> 200 MHz </td> 
 <td style="width:51.45pt;"> 400 MHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;width:81.7pt;"> Expected Transmission ON </td> 
 <td style="width:35.45pt;"> 60 </td> 
 <td style="width:47.8pt;"> 22.1 </td> 
 <td style="width:49.6pt;"> 21.1 </td> 
 <td style="width:49.6pt;"> 22.1 </td> 
 <td style="width:51.45pt;"> N/A </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;width:81.7pt;"> power for DFT-s-OFDM </td> 
 <td style="width:35.45pt;"> 120 </td> 
 <td style="width:47.8pt;"> 22.1 </td> 
 <td style="width:49.6pt;"> 21.1 </td> 
 <td style="width:49.6pt;"> 22.1 </td> 
 <td style="width:51.45pt;"> 21.1 </td> 
 </tr> 
 <tr> 
 <td colspan="2" style="width:117.15pt;"> Power tolerance </td> 
 <td colspan="4" style="vertical-align:top;width:7cm;"> ± (14+TT)dB </td> 
 </tr> 
 <tr> 
 <td colspan="6" style="width:315.6pt;"> Note 1:&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 功率下限不得超过第6.3.2.3条定义的最小输出功率要求，功率上限应不超过第6.2.1.3条定义的最大EIRP。 </td> 
 </tr> 
 </tbody> 
</table>

**Table 6.3.3.2.5-3: Test Tolerance for OFF power**

FFS

**Table 6.3.3.2.5-4: Test Tolerance for ON power**

FFS

**Table 6.3.3.2.5-5: Relaxation required for OFF power for PC3 UEs**

<table style="width:567px;"> 
 <tbody> 
 <tr> 
 <td style="vertical-align:top;width:124.9pt;"> Operating band </td> 
 <td style="width:75.1pt;"> 50 MHz </td> 
 <td style="vertical-align:top;width:75.1pt;"> 100 MHz </td> 
 <td style="vertical-align:top;width:75.05pt;"> 200 MHz </td> 
 <td style="vertical-align:top;width:75.1pt;"> 400 MHz </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;width:124.9pt;"> n257, n258, n261 </td> 
 <td style="width:75.1pt;"> 19.4 dB </td> 
 <td style="vertical-align:top;width:75.1pt;"> 22.4 dB </td> 
 <td style="vertical-align:top;width:75.05pt;"> 25.4 dB </td> 
 <td style="vertical-align:top;width:75.1pt;"> 28.4 dB </td> 
 </tr> 
 <tr> 
 <td style="vertical-align:top;width:124.9pt;"> n260 </td> 
 <td style="width:75.1pt;"> 21.5 dB </td> 
 <td style="vertical-align:top;width:75.1pt;"> 24.5 dB </td> 
 <td style="vertical-align:top;width:75.05pt;"> 27.5 dB </td> 
 <td style="vertical-align:top;width:75.1pt;"> 30.5 dB </td> 
 </tr> 
 </tbody> 
</table>