AD7797芯片驱动调试

待我称王封你为后i 2023-01-17 10:56 115阅读 0赞

今天在测试拉力传感器，调校后，发现拉力值还是零。查看AD采样值，结果如图：

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70][]

先不去分析为啥是零，只看AD采样数据就不对，怎么会偏差这么大，而且有极大值和极小值。

驱动是同事写的，目前已经不负责这个项目了，我只能一点点来看手册调试。

一、AD7797引脚

引脚图，如下图：

![20210429084245279.png][]

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 1][]

注：和通信相关的就是标注的几个引脚，单个芯片（CS可以一直拉低，表示一直选中，不建议这么做）。DOUT/RDY为低表示

转换完成，数据读走或者在数据更新之前为高（数据跟新完后为低）。

时序图：

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 2][]

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 3][]

二、复位

AD7797有上电复位和软件复位。

![20210429084938594.png][]

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 4][]

说的很清楚了，DIN引脚保持至少32个时钟周期，则复位；复位后，经过500us间隔

才能和AD7797通信。

void reset_Ad7797(void)  
    {    
        uint8_t i=0;
        SAFE_ATOM_CODE(
            //AD_CS_LOW;
            //80nS
            AD_DIN_HIGH;
            for(i = 0; i < 36; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                AD_SCLK_HIGH;
                //100ns
            }  
            //AD_CS_HIGH;
            //80nS
            //__NOP();
        )
        //500us
        delay(300);
    }

三、读写寄存器

AD7797怎么读写寄存，怎么配置，请看数据手册，这里只讲大概思路。

（数据传输的时候，先传输高字节的高bit）

**COMMUNICATION REGISTER**

所以有的后续操作，都需要先操作通信寄存器。

CR7写0，可以操作本寄存器；CR6写0，代表后续是写操作；CR6写1，代表后续是读操作；RS2-RS0表示后续操作寄存器地址。

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 5][]

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 6][]

STATUS REGISTER

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 7][]

MODE REGISTER

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 8][]

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 9][]

转换模式有两种：单次转换模式和连续转换模式；转换完后，OUT/RDY为低；

校准模式有三种：内准基准零点校准，系统零点校准和系统满量程校准（系统校准需要硬件支持）。

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 10][]

CONFIGURATION REGISTER

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 11][]

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 12][]

读写时候，按着时序图：

1）写入数据：MCU低电平改变；AD7797高电平读取；

2）读取数据：AD7797电平输出；MCU高电平读取；

测试ID寄存器，发现读取是0x5A，芯片没有焊接错误，只能在时序上看：

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 13][]

最后一个Bit在下降沿变低，查看时序图：

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 14][]

最后一个Bit要求上升沿后10ns读取，反应没这么快；下降沿后80ns数据就稳定了，而读取IO需要百ns级，因此

改成下降沿读取，测试成功。

void write_8bit(uint8_t chAddress,uint8_t writedata)  
    {    
        U8 i;  
        union{
            uint8_t chCRBD[2];
            struct{
            uint8_t         :2;
            uint8_t Cread   :1;
            uint8_t chRS    :3;
            uint8_t RW      :1;
            uint8_t WEN     :1;
            };
        }tCRBD = {0};
        tCRBD.chCRBD[0] = 0;
        tCRBD.chCRBD[1] = writedata;
        tCRBD.WEN = 0;
        tCRBD.RW  = 0;
        tCRBD.chRS= chAddress;
        SAFE_ATOM_CODE(
            //AD_CS_LOW;
            //80nS
            for(i = 0; i < 16; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                if(tCRBD.chCRBD[i>>3] & 0x80){
                    AD_DIN_HIGH;
                }else{
                    AD_DIN_LOW;
                }
                AD_SCLK_HIGH;
                //100ns
                tCRBD.chCRBD[i>>3] = tCRBD.chCRBD[i>>3] << 1;
            }
            //AD_CS_HIGH;
            //80nS
        ) 
        AD_DIN_HIGH;
    }
    
    
    void write_16bit(uint8_t chAddress,uint16_t writedata)  
    {    
        U8 i;  
        union{
            uint8_t chCRBD[3];
            struct{
            uint8_t         :2;
            uint8_t Cread   :1;
            uint8_t chRS    :3;
            uint8_t RW      :1;
            uint8_t WEN     :1;
            };
        }tCRBD = {0};
        tCRBD.chCRBD[0] = 0;
        tCRBD.chCRBD[1] = (writedata>>8) & 0x00FF;
        tCRBD.chCRBD[2] = writedata & 0x00FF;
        tCRBD.WEN = 0;
        tCRBD.RW  = 0;
        tCRBD.chRS= chAddress;
        SAFE_ATOM_CODE(
            //AD_CS_LOW;
            //80nS
            for(i = 0; i < 24; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                if(tCRBD.chCRBD[i>>3] & 0x80){
                    AD_DIN_HIGH;
                }else{
                    AD_DIN_LOW;
                }
                AD_SCLK_HIGH;
                //100ns
                tCRBD.chCRBD[i>>3] = tCRBD.chCRBD[i>>3] << 1;
            }
            //AD_CS_HIGH;
            //80nS
        ) 
        AD_DIN_HIGH;
    }
    
    void write_24bit(uint8_t chAddress,uint32_t writedata)  
    {    
        U8 i;  
        union{
            uint8_t chCRBD[4];
            struct{
            uint8_t         :2;
            uint8_t Cread   :1;
            uint8_t chRS    :3;
            uint8_t RW      :1;
            uint8_t WEN     :1;
            };
        }tCRBD = {0};
        tCRBD.chCRBD[0] = 0;
        tCRBD.chCRBD[1] = (writedata>>16) & 0x000000FF;
        tCRBD.chCRBD[2] = (writedata>>8)  & 0x000000FF;
        tCRBD.chCRBD[3] = writedata & 0x000000FF;
        tCRBD.WEN = 0;
        tCRBD.RW  = 0;
        tCRBD.chRS= chAddress;
        SAFE_ATOM_CODE(
            //AD_CS_LOW;
            //80nS
            for(i = 0; i < 32; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                if(tCRBD.chCRBD[i>>3] & 0x80){
                    AD_DIN_HIGH;
                }else{
                    AD_DIN_LOW;
                }
                AD_SCLK_HIGH;
                //100ns
                tCRBD.chCRBD[i>>3] = tCRBD.chCRBD[i>>3] << 1;
            }
            //AD_CS_HIGH;
            //80nS
        ) 
        AD_DIN_HIGH;
    }

uint8_t read_8bit(uint8_t chAddress)  
    {     
        uint8_t readdata = 0;  
        uint8_t i;  
        union{
            uint8_t chCRBD;
            struct{
            uint8_t         :2;
            uint8_t Cread   :1;
            uint8_t chRS    :3;
            uint8_t RW      :1;
            uint8_t WEN     :1;
            };
        }tCRBD = {0};
        tCRBD.chCRBD= 0;
        tCRBD.WEN = 0;
        tCRBD.RW  = 1;
        tCRBD.chRS= chAddress;
        SAFE_ATOM_CODE(
            //AD_CS_LOW;
            //80nS
            for(i = 0; i < 8; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                if(tCRBD.chCRBD & 0x80){
                    AD_DIN_HIGH;
                }else{
                    AD_DIN_LOW;
                }
                AD_SCLK_HIGH;
                //100ns
                tCRBD.chCRBD = tCRBD.chCRBD<<1;
            }
            AD_DIN_HIGH;
            for(i = 0; i < 8; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                readdata = readdata << 1;
                if(AD_DOUT){
                    readdata += 1;
                }
                AD_SCLK_HIGH;
                //100ns
            }
            //AD_CS_HIGH;
            //80nS
        ) 
        return readdata;
    }
    
    
    uint16_t read_16bit(uint8_t chAddress)  
    {     
        uint16_t readdata = 0;  
        uint8_t  i;  
        union{
            uint8_t chCRBD;
            struct{
            uint8_t         :2;
            uint8_t Cread   :1;
            uint8_t chRS    :3;
            uint8_t RW      :1;
            uint8_t WEN     :1;
            };
        }tCRBD = {0};
        tCRBD.chCRBD= 0;
        tCRBD.WEN = 0;
        tCRBD.RW  = 1;
        tCRBD.chRS= chAddress;
        SAFE_ATOM_CODE(
            //AD_CS_LOW;
            //80nS
            for(i = 0; i < 8; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                if(tCRBD.chCRBD & 0x80){
                    AD_DIN_HIGH;
                }else{
                    AD_DIN_LOW;
                }
    
                AD_SCLK_HIGH;
                //100ns
                tCRBD.chCRBD = tCRBD.chCRBD<<1;
            }
            AD_DIN_HIGH;
            for(i = 0; i < 16; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                readdata = readdata << 1;
                if(AD_DOUT){
                    readdata += 1;
                }
                AD_SCLK_HIGH;
                //100ns
            }
            //AD_CS_HIGH;
            //80nS
        )
        return readdata;
    }
    
    uint32_t read_24bit(uint8_t chAddress)  
    {     
        uint32_t readdata = 0;  
        uint8_t  i;  
        union{
            uint8_t chCRBD;
            struct{
            uint8_t         :2;
            uint8_t Cread   :1;
            uint8_t chRS    :3;
            uint8_t RW      :1;
            uint8_t WEN     :1;
            };
        }tCRBD = {0};
        tCRBD.chCRBD= 0;
        tCRBD.WEN = 0;
        tCRBD.RW  = 1;
        tCRBD.chRS= chAddress;
        SAFE_ATOM_CODE(
            //AD_CS_LOW;
            //80nS
            for(i = 0; i < 8; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                if(tCRBD.chCRBD & 0x80){
                    AD_DIN_HIGH;
                }else{
                    AD_DIN_LOW;
                }
                AD_SCLK_HIGH;
                //100ns
                tCRBD.chCRBD = tCRBD.chCRBD<<1;
            }
            AD_DIN_HIGH;
            for(i = 0; i < 24; i++)  
            {  
                AD_SCLK_LOW;
                //100ns
                readdata = readdata << 1;
                if(AD_DOUT){
                    readdata += 1;
                }
                AD_SCLK_HIGH;
                //100ns
            }
            //AD_CS_HIGH;
            //80nS
        )
        return readdata;
    }

四、读取数据

1、初始化

void Init_ad7797(void)
    {
    	unsigned char id = 0;
        unsigned int  con= 0;
        //复位
        reset_Ad7797();
        //读取复位状态
        while(1){
            if(0x08 == (read_8bit(AD7797_SR) & 0x08)){
                break;
            }
        }
        //校准
        sys_calibration();
        //读取ID
        while(1){
            if(0x5B == read_8bit(AD7797_IDR)){
                break;
            }
        }
        //设置模式
        Ad7797_Ini();
    }

校准：

void sys_calibration(void)    
    {  
        //内部零点校准
        write_16bit(AD7797_MR,0x8009);
        while(0x00 != (read_8bit(AD7797_SR) & 0x80));
        //系统零点校准
        //write_16bit(AD7797_MR,0xC009);
        //系统满量程校准
        //write_16bit(AD7797_MR,0xE009);
    }

设置模式：

void Ad7797_Ini(void)     
    {     	
    //	write_16bit(AD7797_MR,0x0710);
    
    //    while(1){
    //        if(0x0710 == read_16bit(AD7797_MR)){
    //            break;
    //        }
    //    }
    
        while(1){
            write_16bit(AD7797_MR,0x200A);
            if(0x200A == read_16bit(AD7797_MR)){
                break;
            }
        }
    }

读取数据流程：

单词模式：

write\_16bit(AD7797\_MR,0x200A);//启动转换（每次转换完成后，都要从新启动）

等待转换完成，DOUT/RDY引脚边变低

读取数据：

read\_24bit(AD7797\_DR)

连续模式：

write\_16bit(AD7797\_MR,0x000A);//配置模式（启动一次就行）

等待转换完成，DOUT/RDY引脚边变低

读取数据：

read\_24bit(AD7797\_DR)

采样数据：

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 15][]

2021.04.30

昨天把CS一直使能的驱动调试没有问题了，同事说不建议这样用，还是要启用CS，于是今天又把CS使能了，但是发现一个奇怪的问题，

就是AD一直读取不到数据，查看是读取不到DOUT/RDY拉低，肯定不是驱动函数的事，只能从时序着手了。查看单词读取时序：

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 16][]

启动转换后，等待转换期间，CS要保持低电平，修改逻辑后，测试OK。

下图是连续转换模式，需要CS一直使能：

![watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 17][]

[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70]: /images/20221021/1c65aff1021c4473826b40f885c49c39.png
[20210429084245279.png]: /images/20221021/2e89d703f6484b1f8f49eec00efe500c.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 1]: /images/20221021/5a2ca7465327456b89d33b00d51f9541.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 2]: /images/20221021/a3e2b91c06a84669b94eb61a5692db5d.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 3]: /images/20221021/a28a284e2e464e9dabc86415a81f84e6.png
[20210429084938594.png]: /images/20221021/38b5db3c47864cac903529c37879cf0a.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 4]: /images/20221021/8e896bce49c0459c8b13fc85193f900e.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 5]: /images/20221021/37c703544a4a4d859d27bd15dd58f3ee.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 6]: /images/20221021/c902ffb367c349cf8e644df957ab63c5.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 7]: /images/20221021/a949c5eaf4f54a24ba80139dc320995b.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 8]: /images/20221021/ecb136994471437aaed39e1e7814f37f.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 9]: /images/20221021/5c8a687a1d1d4df68fc8796628b4169e.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 10]: /images/20221021/6a2c9084f8974260982ba4505314456b.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 11]: /images/20221021/5bd4c2084af74a368b61286ed74b5cd5.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 12]: /images/20221021/38cb0f8ee99b4094aa0dc7efe675c114.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 13]: /images/20221021/7115829f30d942669047d0070eb5e698.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 14]: /images/20221021/93aa30e6842b4fbda175ec6c4f94f94f.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 15]: /images/20221021/5122e58473a84e4e9615b1303370c457.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 16]: /images/20221021/9b8d7aa00869470d92f0f0548a0cbc31.png
[watermark_type_ZmFuZ3poZW5naGVpdGk_shadow_10_text_aHR0cHM6Ly9ibG9nLmNzZG4ubmV0L3d1aGVueW91eXV5b3V5dQ_size_16_color_FFFFFF_t_70 17]: /images/20221021/8837524c73724695a4dd76e226313519.png